价格: 电议
物流: 暂无物流地址| 买家支付运费
可销售总量: 0件
手机: 13621511555 邮箱: huangsifa@163.com
传真: 0510-82359678 地址: 江苏 无锡市
邮箱:
手机:
手动带气动放料阀产品介绍:
一、气动放料阀工作原理:
1、轻松转动手轮,将切换手柄推移到(分)指示牌,即可进*动操作。
2、当气源进入电磁阀后,电磁阀自动开戾上(或下)输气口,电磁阀接通电源时,阀门自动开启,断电时阀门自动关闭。红色按钮为手动调试使用开关按钮。
3、当气源进入气缸上部时,将活塞推向下部,即关闭阀门。
4、当气源进入气缸下部时,将活塞推向上部,即开启阀门。
5、连续作业时,按上述作往返动力。
二、手动放料阀工作原理:
1、关闭气源,在无气源压力下,轻松转动手轮,逐渐使切换手柄推移至(合)指示牌,即可进行手动操作。
2、转动手轮,逆时针阀门开,顺时针阀门关。
三、气动执行器的日常维护工作:
1、氮源应保持干燥和清洁,定期对过滤器进行放水。
2、保持氮源压力正常(0.4~0.7Mpa),电气部分的电源信号无短路或断路故障,防止水,保证电磁阀和回信开关正常工作。
3、在正常工作情况下,每月检验一次,每年检修一次。
四、手动带气动放料阀注意:
1、气动操作时,必须将切换手柄完全推移至(分)指示处,切莫使手柄 处于分合不明的状态,否则,将会损坏内部机件。
2、严禁敲打或撞击手柄。
五、手动带气动放料阀安装时应注意以下事项:
1、保持阀瓣于封圈密封面无污垢、泥沙.。
2、检查填料于活塞是否密封良好, 不得私自拆装,要技术人员的指导下。
3、气缸拆下长时间不用时,所有加工表面应涂防锈油,进、排气口应加防尘堵塞。
六、在手动带气动放料阀安装后进行管路强度试压时阀瓣必须修全部开启:
1、安装前应仔细核对使用情况是否与本阀门性能相符。
2、检查各部件是否拧紧。
3、应保证在工作、维护和更换上的方便。
七、手动带气动放料阀在使用过程中应定期检查:
1、请检查阀杆和填料磨损 情况,以免泄漏 。
2、定期对气动头表面除尘和维护。
Manual pneumatic feeding valve product i*oduction:
The working principle, pneumatic feeding valve:
1, turn the handwheel, easily will switch handle goes on to the () sign, pneumatic operation can be achieved.
2, when the air into the electromagnetic valve, electromagnetic valve automatically open crime (or below) gas mouth, electromagnetic valve switching power supply, valve automatically opens, the valve automatically shut off when the power outage. Red button switch button for manual debugging use.
3, when the upper air into the cylinder, the piston to the bottom, or close the valve.
4, when the air into the lower part of the cylinder, the piston to the top, the open valve.
5, continuous operation, according to the power back and forth.
Second, the manual feeding valve working principle:
1, close the gas source, in the absence of air pressure, easy to turn the handwheel, gradually make the switch handle on the sign (us), can be manually.
2, turn the handwheel, turn the valve to open, and valve clockwise.
Three, the routine maintenance of pneumatic actuators:
1, the nitrogen source should be kept dry and clean, to drain the filter regularly.
2, keep nitrogen source pressure is normal (0.4 ~ 0.7 Mpa), part of the electrical power signal no short circuit or open circuit fault, prevent water, guarantee the normal work of the solenoid valve and reply switch.
3, under normal working condition, inspection once a month, maintenance once a year.
Four pneumatic feeding valve, manual take note:
1, pneumatic operation, switch handle must be completely goes to (points) instructions, do not make the handle in the condition of unknown points or, otherwise, will damage the internal parts.
2, it is strictly prohibited to knock or hit the handle.
Five, the manual pneumatic feeding valve when installation should pay attention to the following items:
1, keep the disc in sealing ring sealing surface with no dirt, sediment..
2, check if packing in piston seal is good, not to rob the tear open outfit, under the guidance of technical staff.
3, remove the cylinder for a long time need not when, all of the processing surface should be coated rust-proof oil, inlet and outlet should add dustproof plug.
Six, in manual with pneumatic feeding valve is installed in line strength test disc must fix all opened:
1, before installation shall carefully check whether the usage is consistent with the valve performance.
2, check the parts are on tight.
3, should guarantee in the work, and the ease of maintenance and replacement.
Seven, manual pneumatic feeding valve in use process should be checked regularly:
1, please check the abrasion of stem and packing, in order to *oid leakage.
2, dust on the surface of a pneumatic head and maintenance on a regular basis.
www.klevalve.com 电话:0510-82359668 传真:0510-82359678 电子邮件:kle@klevalve.com
欢迎来电索取详细技术资料,科莱恩KLEIN阀门!
注册资金:1000万-5000万
联系人:黄思发
固话:0510-82359668
移动手机:13621511555
企业地址:江苏 无锡市 北塘区